Monitoring & Sensors

- All hot, neutral, and safety ground buses installed, fully pre-wired - All circuit label positions are backlit on standard panels - No kit required - "ON" indicating LEDs installed in all circuit posistions - Maximum panel amperage - 100 Amperes

- All hot, neutral, and safety ground buses installed, fully pre-wired - All circuit label positions are backlit on standard panels - No kit required - "ON" indicating LEDs installed in all circuit posistions - Maximum panel amperage - 100 Amperes

- Simple 2-wire connection - Meter senses and powers from coil slipped over wire to be measured - Includes AC current transformer

- For use with AC Ammeters

No description available.

- For use with AC Ammeters

- Displays frequency from 40 to 90 Hertz - 3 levels of display brightness - Splashproof front - Manual sleep mode blanks display for power conservation

- Displays amperage from 0 to 150 Amps - Displays voltage from 80 to 270 Volts - Displays power from 0 to 35 Kilowatts - Displays frequency from 40 to 90 Hertz - High and low voltage and high amperage alarms, both audio and visual - 3 levels of display brightness - Programmable sleep mode blanks display for power conservation - Splashproof front - Includes current transformer

No description available.

- Provides electrical insulation for exposed panel backs - Provides mechanical protection for panel backs protruding into lockers - Lightweight material is easily drilled for wire entrance and exit - Meets ABYC requirements for panels with combined AC and DC Covers a panel, or other object, up to 5-1/4" long x 3-3/4" width x 3" deep.

No description available.

No description available.

No description available.

- 120 AC labels printed in French. - Based on 8067 English label set - Reinforced, weatherproof material - Used on Contura Waterproof Fuse Panels - Used on ST Glass Fuse Blocks - Used on all Raised Rocker and Toggle Circuit Breaker Panels

No description available.

No description available.

No description available.

- For use with DC Ammeters - For continuous operation, it is recommended that shunts not to be run at more than two-thirds (66%) the rated current under normal conditions

- For use with DC Ammeters - For continuous operation, it is recommended that shunts not to be run at more than two-thirds (66%) the rated current under normal conditions

- For use with DC Ammeters - For continuous operation, it is recommended that shunts not to be run at more than two-thirds (66%) the rated current under normal conditions

Can be configured to be used as one of the following battery saving productsTimer Disconnect - 12V signal triggers relay to connect battery power to devices - When signal is removed the timer is activated and will disconnect devices after a preset time - Timer ranges from 15 minutes to 4 hours Low Voltage Disconnect - 12V signal triggers relay to connect battery power to devices. - After 12V signal is removed, device senses low battery voltage and automatically disconnects devices. - Low voltage setting can be used in conjunction with Timer Disconnect. Low voltage will disconnect devices prior to preset time to preserve battery power Automatic Charging Relay - Automatically combines two batteries when charging, and isolates them when discharging - Single side sensing design only monitors the voltage of the start battery - Ideal for auxiliary batteries that are AGM or significantly larger than the start battery Solenoid - 12V signal will connect or disconnect relay without any time delay

- All positive, negative and grounding buses installed, fully pre-wired - Panels with meters include toggle switch for mounting up to 3 battery banks - All panels with analog meters are owner upgradable to 24 Volts with 8240 or 8243 (18-32V DC meters) - All circuit label positions are backlit on standard panels - No kit required - "ON" indicating LEDs installed in all circuit positions

- All positive, negative and grounding buses installed, fully pre-wired - Panels with meters include toggle switch for mounting up to 3 battery banks - All panels with analog meters are owner upgradable to 24 Volts with 8240 or 8243 (18-32V DC meters) - All circuit label positions are backlit on standard panels - No kit required - "ON" indicating LEDs installed in all circuit positions

- Easily installed in any Blue Sea Systems circuit breaker panel - Simple push-in installation mounts in any thickness material - Useful as general indicator and alarm lights

- Easily installed in any Blue Sea Systems circuit breaker panel - Simple push-in installation mounts in any thickness material - Useful as general indicator and alarm lights

- Easily installed in any Blue Sea Systems circuit breaker panel - Simple push-in installation mounts in any thickness material - Useful as general indicator and alarm lights

Monitors AC Amps, Volts, Hzs on large, bright display. Supports programmable current transformer ratios. Accurately measure and monitor AC amperage, voltage and Hz. (measures 2 voltages and 2 circuits) - Auto-dimming, bright OLED display is easy to read - Easy to adjust - 80dB alarm on all models - Isolated MOSFET relay

Monitors AC Voltage on large, bright display. Accurately measure and monitors the voltage of your AC system. (measures 2 independent circuits or 1 double phase circuit) - Auto-dimming, bright OLED display is easy to read - Easy to adjust - 80dB alarm on all models - Isolated MOSFET relay

The M2 Organic LED Digital Monitor measures essential electrical system parameters with adjustable alarms and an auto-dimming display. The M2 Monitors include a MOSFET External Circuit Relay (ECR) which can be used to control external circuits based on any value measured by the M2. - Auto-dimming, bright Organic LED display is easy to read - 80dB alarm on all models - Isolated 500mA MOSFET relay - Intuitive tank level monitoring - Monitor up to 4 tanks - Auto calibration for unique tank shapes - Compatible with common sending units

- Clamp allows measurement of AC and DC current in wires without disturbing the circuits or contacting live terminals - Auto range simplifies operation: 0.01-400 Amps, 0.001-600 Volts - Auto power-off selection - power turns off automatically after 10 minutes of non-use - True RMS - required for accurate measurement of inverter output - Large digital display makes reading measurements easy - Data hold - press "HOLD" button during measurement to lock reading value - Test leads included with meter